? semiconductor components industries, llc, 2013 october, 2013 ? rev. 12 1 publication order number: CAT93C86/d CAT93C86 16 kb microwire serial eeprom description the CAT93C86 is a 16 kb serial eeprom memory device which is configured as either registers of 16 bits (org pin at v cc ) or 8 bits (org pin at gnd). each register can be written (or read) serially by using the di (or do) pin. the CAT93C86 is manufactured using on semiconductor?s advanced cmos eeprom floating gate technology. the device is designed to endure 1,000,000 program/erase cycles and has a data retention of 100 years. the device is available in 8 ? pin dip and 8 ? pin soic packages. features ? high speed operation: 3 mhz / v cc = 5 v ? low power cmos technology ? 1.8 v to 5.5 v operation ? selectable x8 or x16 memory organization ? self ? timed write cycle with auto ? clear ? hardware and software write protection ? power ? up inadvertent write protection ? sequential read ? program enable (pe) pin ? 1,000,000 program/erase cycles ? 100 year data retention ? industrial and extended temperature ranges ? 8 ? lead pdip and soic packages ? these devices are pb ? free, halogen free/bfr free, and rohs compliant org do CAT93C86 sk gnd v cc figure 1. functional symbol pe cs di note: when the org pin is connected to v cc , the x16 or ganization is selected. when it is connected to ground, the x8 pin is selected. if the org pin is left unconnected, then an internal pull ? up device will select the x16 organization. http://onsemi.com pin configuration do di sk cs 1 see detailed ordering and shipping information in the package dimensions section on page 10 of this data sheet. ordering information soic ? 8 v, w suffix case 751bd pdip (l), soic (v, x) pdip ? 8 l suffix case 646aa chip select cs clock input sk serial data input di serial data output do power supply v cc ground gnd function pin name pin function memory organization org program enable pe soic ? 8 x suffix case 751be gnd org pe v cc sk cs v cc pe 1 di do gnd org soic (w)* * not recommended for new designs
CAT93C86 http://onsemi.com 2 table 1. absolute maximum ratings parameters ratings units temperature under bias ? 55 to +125 c storage temperature ? 65 to +150 c voltage on any pin with respect to ground (note 1) ? 2.0 to +v cc +2.0 v v cc with respect to ground ? 2.0 to +7.0 v package power dissipation capability (t a = 25 c) 1.0 w lead soldering temperature (10 seconds) 300 c output short circuit current (note 2) 100 ma stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. 1. the minimum dc input voltage is ? 0.5 v. during transitions, inputs may undershoot to ? 2.0 v for periods of less than 20 ns. maximum dc voltage on output pins is v cc +0.5 v, which may overshoot to v cc +2.0 v for periods of less than 20 ns. 2. output shorted for no more than one second. no more than one output shorted at a time. table 2. reliability characteristics symbol parameter reference test method min units n end (note 3) endurance mil ? std ? 883, test method 1033 1,000,000 cycles/byte t dr (note 3) data retention mil ? std ? 883, test method 1008 100 years v zap (note 3) esd susceptibility mil ? std ? 883, test method 3015 2000 v i lth (notes 3, 4) latch ? up jedec standard 17 100 ma 3. these parameters are tested initially and after a design or process change that affects the parameter. 4. latch ? up protection is provided for stresses up to 100 ma on address and data pins from ? 1 v to v cc +1 v. table 3. d.c. operating characteristics (v cc = +1.8 v to +5.5 v unless otherwise specified.) symbol parameter test conditions min typ max units i cc1 power supply current (write) f sk = 1 mhz; v cc = 5.0 v 3 ma i cc2 power supply current (read) f sk = 1 mhz; v cc = 5.0 v 500 a i sb1 power supply current (standby) (x8 mode) cs = 0 v org = gnd 10 a i sb2 power supply current (standby) (x16 mode) cs = 0 v org = float or v cc 0 10 a i li input leakage current v in = 0 v to v cc 1 a i lo output leakage current (including org pin) v out = 0 v to v cc , cs = 0 v 1 a v il1 input low voltage 4.5 v v cc < 5.5 v ? 0.1 0.8 v v ih1 input high voltage 4.5 v v cc < 5.5 v 2 v cc + 1 v v il2 input low voltage 1.8 v v cc < 4.5 v 0 v cc x 0.2 v v ih2 input high voltage 1.8 v v cc < 4.5 v v cc x 0.7 v cc + 1 v v ol1 output low voltage 4.5 v v cc < 5.5 v; i ol = 2.1 ma 0.4 v v oh1 output high voltage 4.5 v v cc < 5.5 v; i oh = ? 400 a 2.4 v v ol2 output low voltage 1.8 v v cc < 4.5 v; i ol = 1 ma 0.2 v v oh2 output high voltage 1.8 v v cc < 4.5 v; i oh = ? 100 a v cc ? 0.2 v
CAT93C86 http://onsemi.com 3 table 4. pin capacitance (note 5) symbol test conditions min typ max units c out output capacitance (do) v out = 0 v 5 pf c in input capacitance (cs, sk, di, org) v in = 0 v 5 pf table 5. power ? up timing (notes 5, 6) symbol parameter max units t pur power ? up to read operation 1 ms t puw power ? up to write operation 1 ms table 6. a.c. test conditions input rise and fall times 50 ns input pulse voltages 0.4 v to 2.4 v 4.5 v v cc 5.5 v timing reference voltages 0.8 v, 2.0 v 4.5 v v cc 5.5 v input pulse voltages 0.2 x v cc to 0.7 x v cc 1.8 v v cc 4.5 v timing reference voltages 0.5 x v cc 1.8 v v cc 4.5 v table 7. a.c. characteristics symbol parameter test conditions v cc = 1.8 v ? 5.5 v v cc = 2.5 v ? 5.5 v v cc = 4.5 v ? 5.5 v units min max min max min max t css cs setup time 200 100 50 ns t csh cs hold time 0 0 0 ns t dis di setup time 200 100 50 ns t dih di hold time 200 100 50 ns t pd1 output delay to 1 1 0.5 0.15 s t pd0 output delay to 0 c l = 100 pf (note 7) 1 0.5 0.15 s t hz (note 5) output delay to high ? z 400 200 100 ns t ew program/erase pulse width 5 5 5 ms t csmin minimum cs low time 1 0.5 0.15 s t skhi minimum sk high time 1 0.5 0.15 s t sklow minimum sk low time 1 0.5 0.15 s t sv output delay to status valid 1 0.5 0.1 s sk max maximum clock frequency dc 500 dc 1000 dc 3000 khz 5. these parameters are tested initially and after a design or process change that affects the parameter. 6. t pur and t puw are the delays required from the time v cc is stable until the specified operation can be initiated. 7. the input levels and timing reference points are shown in the ?a.c. test conditions? table.
CAT93C86 http://onsemi.com 4 table 8. instruction set instruction start bit opcode address data comments x8 x16 x8 x16 read 1 10 a10 ? a0 a9 ? a0 read address an? a0 erase 1 11 a10 ? a0 a9 ? a0 clear address an? a0 write 1 01 a10 ? a0 a9 ? a0 d7 ? d0 d15 ? d0 write address an? a0 ewen 1 00 11xxxxxxxxx 11xxxxxxxx write enable ewds 1 00 00xxxxxxxxx 00xxxxxxxx write disable eral 1 00 10xxxxxxxxx 10xxxxxxxx clear all addresses wral 1 00 01xxxxxxxxx 01xxxxxxxx d7 ? d0 d15 ? d0 write all addresses device operation the CAT93C86 is a 16,384 ? bit nonvolatile memory intended for use with industry standard microprocessors. the CAT93C86 can be organized as either registers of 16 bits or 8 bits. when organized as x16, seven 13 ? bit instructions control the reading, writing and erase operations of the device. when organized as x8, seven 14 ? bit instructions control the reading, writing and erase operations of the device. the CAT93C86 operates on a single power supply and will generate on chip, the high voltage required during any write operation. instructions, addresses, and write data are clocked into the di pin on the rising edge of the clock (sk). the do pin is normally in a high impedance state except when reading data from the device, or when checking the ready/busy status after a write operation. the ready/busy status can be determined after the start of a write operation by selecting the device (cs high) and polling the do pin; do low indicates that the write operation is not completed, while do high indicates that the device is ready for the next instruction. if necessary, the do pin may be placed back into a high impedance state during chip select by shifting a dummy ?1? into the di pin. the do pin will enter the high impedance state on the falling edge of the clock (sk). placing the do pin into the high impedance state is recommended in applications where the di pin and the do pin are to be tied together to form a common di/o pin. the format for all instructions sent to the device is a logical ?1? start bit, a 2 ? bit (or 4 ? bit) opcode, 10 ? bit address (an additional bit when organized x8) and for write operations a 16 ? bit data field (8 ? bit for x8 organizations). note: the write, erase, write all and erase all instructions require pe = 1. if pe is left floating, 93c86 is in program enabled mode. for write enable and write disable instruction pe = don?t care. read upon receiving a read command and an address (clocked into the di pin), the do pin of the ca t93c86 will come out of the high impedance state and, after sending an initial dummy zero bit, will begin shifting out the data addressed (msb first). the output data bits will toggle on the rising edge of the sk clock and are stable after the specified time delay (t pd0 or t pd1 ). after the initial data word has been shifted out and cs remains asserted with the sk clock continuing to toggle, the device will automatically increment to the next address and shift out the next data word in a sequential read mode. as long as cs is continuously asserted and sk continues to toggle, the device will keep incrementing to the next address automatically until it reaches to the end of the address space, then loops back to address 0. in the sequential read mode, only the initial data word is preceeded by a dummy zero bit. all subsequent data words will follow without a dummy zero bit. write after receiving a write command, address and the data, the cs (chip select) pin must be deselected for a minimum of t csmin . the falling edge of cs will start the self clocking clear and data store cycle of the memory location specified in the instruction. the clocking of the sk pin is not necessary after the device has entered the self clocking mode. the ready/busy status of the CAT93C86 can be determined by selecting the device and polling the do pin. since this device features auto ? clear before write, it is not necessary to erase a memory location before it is written into.
CAT93C86 http://onsemi.com 5 figure 2. synchronous data timing sk di cs do valid valid data valid t css t dis t skhi t sklow t dis t dih t csh t csmin t pd0 , t pd1 figure 3. read instruction timing sk cs di do high ? z 11 0 dummy 0 don?t care a n a n ? 1 a 0 address + n d 15 . . . or d 7 . . . address + 2 d 15 . . . d 0 or d 7 . . . d 0 address + 1 d 15 . . . d 0 or d 7 . . . d 0 d 15 . . . d 0 or d 7 . . . d 0 111111111111111 figure 4. write instruction timing sk cs di do standby high ? z high ? z 101 busy ready status t hz t ew t sv verify a n ? 1 a n a 0 d 0 d n t csmin
CAT93C86 http://onsemi.com 6 erase upon receiving an erase command and address, the cs (chip select) pin must be deasserted for a minimum of t csmin . the falling edge of cs will start the self clocking clear cycle of the selected memory location. the clocking of the sk pin is not necessary after the device has entered the self clocking mode. the ready/busy status of the ca t93c86 can be determined by selecting the device and polling the do pin. once cleared, the content of a cleared location returns to a logical ?1? state. erase/write enable and disable the CAT93C86 powers up in the write disable state. any writing after power ? up or after an ewds (write disable) instruction must first be preceded by the ewen (write enable) instruction. once the write instruction is enabled, it will remain enabled until power to the device is removed, or the ewds instruction is sent. the ewds instruction can be used to disable all CAT93C86 write and clear instructions, and will prevent any accidental writing or clearing of the device. data can be read normally from the device regardless of the write enable/disable status. erase all upon receiving an eral command, the cs (chip select) pin must be deselected for a minimum of t csmin . the falling edge of cs will start the self clocking clear cycle of all memory locations in the device. the clocking of the sk pin is not necessary after the device has entered the self clocking mode. the ready/busy status of the CAT93C86 can be determined by selecting the device and polling the do pin. once cleared, the contents of all memory bits return to a logical ?1? state. write all upon receiving a wral command and data, the cs (chip select) pin must be deselected for a minimum of t csmin . the falling edge of cs will start the self clocking data write to all memory locations in the device. the clocking of the sk pin is not necessary after the device has entered the self clocking mode. the ready/busy status of the CAT93C86 can be determined by selecting the device and polling the do pin. it is not necessary for all memory locations to be cleared before the wral command is executed. figure 5. erase instruction timing sk cs di do standby high ? z high ? z 1 busy ready status 11 verify t hz a n a n ? 1 a 0 t cs t sv t ew
CAT93C86 http://onsemi.com 7 package dimensions pdip ? 8, 300 mils case 646aa ? 01 issue a e1 d a l eb b2 a1 a2 e eb c top view side view end view pin # 1 identification notes: (1) all dimensions are in millimeters. (2) complies with jedec ms-001. symbol min nom max a a1 a2 b b2 c d e e1 l 0.38 2.92 0.36 6.10 1.14 0.20 9.02 2.54 bsc 3.30 5.33 4.95 0.56 7.11 1.78 0.36 10.16 eb 7.87 10.92 e 7.62 8.25 2.92 3.80 3.30 0.46 6.35 1.52 0.25 9.27 7.87
CAT93C86 http://onsemi.com 8 package dimensions soic 8, 150 mils case 751bd ? 01 issue o e1 e a a1 h l c e b d pin # 1 identification top view side view end view notes: (1) all dimensions are in millimeters. angles in degrees. (2) complies with jedec ms-012. symbol min nom max a a1 b c d e e1 e h 0o 8o 0.10 0.33 0.19 0.25 4.80 5.80 3.80 1.27 bsc 1.75 0.25 0.51 0.25 0.50 5.00 6.20 4.00 l 0.40 1.27 1.35
CAT93C86 http://onsemi.com 9 package dimensions soic ? 8, 208 mils case 751be ? 01 issue o e1 eb side view top view e d pin#1 identification end view a1 a l c notes: (1) all dimensions are in millimeters. angles in degrees. (2) complies with eiaj edr-7320. symbol min nom max a a1 b c d e e1 e 0o 8o 0.05 0.36 0.19 5.13 7.75 5.13 1.27 bsc 2.03 0.25 0.48 0.25 5.33 8.26 5.38 l 0.51 0.76
CAT93C86 http://onsemi.com 10 ordering information opn specific device marking pkg type temperature range lead finish shipping CAT93C86li ? g 93c86l pdip ? 8 i = industrial ( ? 40 c to +85 c) nipdau tube, 50 units / tube CAT93C86vi ? g 93c86v soic ? 8, jedec i = industrial ( ? 40 c to +85 c) nipdau tube, 100 units / tube CAT93C86vi ? gt3 93c86v soic ? 8, jedec i = industrial ( ? 40 c to +85 c) nipdau tape & reel, 3000 units / reel CAT93C86wi ? g (note 10) 93c86w soic ? 8, jedec i = industrial ( ? 40 c to +85 c) nipdau tube, 100 units / tube CAT93C86wi ? gt3 (note 10) 93c86w soic ? 8, jedec i = industrial ( ? 40 c to +85 c) nipdau tape & reel, 3000 units / reel CAT93C86xi 93c86x soic ? 8, eiaj i = industrial ( ? 40 c to +85 c) matte ? tin tube, 94 units / tube CAT93C86xi ? t2 93c86x soic ? 8, eiaj i = industrial ( ? 40 c to +85 c) matte ? tin tape & reel, 2000 units / reel 8. all packages are rohs ? compliant (lead ? free, halogen ? free). 9. the standard lead finish is nipdau. 10. not recommended for new designs. 11. for additional package and temperature options, please contact your nearest on semiconductor sales office. 12. for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and ree l packaging specifications brochure, brd8011/d. 13. for detailed information and a breakdown of device nomenclature and numbering systems, please see the on semiconductor devic e nomenclature document, tnd310/d, available at www.onsemi.com on semiconductor and are registered trademarks of semiconductor co mponents industries, llc (scillc). scillc owns the rights to a numb er of patents, trademarks, copyrights, trade secrets, and other intellectual property. a list ing of scillc?s product/patent coverage may be accessed at ww w.onsemi.com/site/pdf/patent ? marking.pdf. scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and s pecifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. all operating parame ters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or a uthorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in whic h the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or us e scillc products for any such unintended or unauthorized appli cation, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unin tended or unauthorized use, even if such claim alleges that scil lc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyrig ht laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5817 ? 1050 CAT93C86/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative
|
